This write-up about how to make 3 Effortless Diy Floating Photo Frames And How to Lower Plexiglass is sponsored by The House Depot as aspect of the #THDProSpective Program. It also has affiliate backlinks. See policies.
Straightforward Do-it-yourself picture frames are actually just one of my most asked for tutorials and oddly enough, until finally now, I didn&rsquot have lots of to share!
.
I truly developed my father a huge Diy custom picture frame as a Xmas reward a pair a long time in the past and shared the tutorial for it listed here. But it used dowels, and a router, and it may well have been a minimal much more involved than most folks are looking for.
So, in this publish, I&rsquom heading to display you how I manufactured three diverse model Tremendous Simple Diy floating photo frames with just two primary applications. I&rsquoll also exhibit you how simple it is to cut plexiglass for them, much too!
.
So if you&rsquore ready to get building, let&rsquos go! I&rsquove got the video tutorial listed here and the step by stage underneath:
Resources AND Elements:
- Miter noticed (or any wooden reducing noticed is good&ndashdoesn&rsquot have to be a MITER noticed)
- Nail Gun (optional, just would make matters more rapidly)
- Wooden Glue
- ¾&Primary sq. dowels
- one×2 boards
- ¼&Primary x one ⅛&Primary lattice trim
- Slender Plexiglass Sheets
- Ryobi A single+ HP Reduce Off Tool (employed to lower plexiglass)
- Clamps (also optional&ndashif you don&rsquot have clamps, you can use CA glue or painters tape in put of clamps to hold items while wooden glue dries)
- Transform buttons
A Be aware About FLOATING Image Frames:
I&rsquom sharing how to make three unique fashion FLOATING photo frames in this tutorial, but the initially step to producing any of them is cutting the plexiglass to the dimensions you want.
.
If you don&rsquot want to use plexiglass for your frames, you can skip this step. But considering the fact that the graphics/images I framed are &ldquofloating&rdquo inside the body, they&rsquore fundamentally sandwiched involving two items of plexiglass. So plexiglass/acrylic is necessary to be able to &ldquofloat&rdquo your photo.
.
To make points easy to alter out in these frames, I also used these change buttons&mdashor I contact them twisty tabs&ndashon the back to maintain the plexiglass in position.  
HOW TO Cut PLEXIGLASS
Commonly, I have my area glass store slice my glass and plexiglass pieces for my initiatives.  But due to the fact these plexiglass parts will be compact and a variety of custom made dimensions, it would be a lot more cost-effective, more rapidly and a lot easier to just slash them myself.
.
I employed some (about) ⅛&rdquo acrylic sheets from Home Depot.  They arrive in numerous sizes, all the way up to a four×8 sheet.  I just grabbed some 11x14s.
I made some simple graphics on my computer system (PicMonkey and Canva are terrific for this!) and also utilised a patch that I won a handful of many years back at a convention for these frames.  You can use a photo, a poster, fabric, whatsoever you want to body for this.
.
I laid them out on my sheet how I appreciated the spacing, then marked where I desired to lower&ndashno measurements listed here&hellipjust eyeballing how I considered the spacing close to the graphic appeared good.
Now, I&rsquove applied the low-priced minimal hand knife they assert will cut plexiglass right before and it was a terrible practical experience with really weak final results.  explanation &rsquove also utilised a jig saw to slice plexiglass and it melts, receives caught, then chips or cracks the sheet.
.
So THIS time, I tried this new Ryobi A person+ HP Compact Minimize Off Software with a plastic cutting blade and was completely impressed with how speedy and clean up the cuts were.
When I 1st saw this tool, I uncovered it form of odd looking.  But following I utilised it, I recognized the notion. 
.
It&rsquos in essence a hybrid concerning a drill and an angle grinder. It cuts like an angle grinder, but it feels a drill with the head turned 90 levels. 
.
It&rsquos compact and light-weight and it&rsquos obtained a ahead and reverse switch to change the blade the two directions.  It&rsquos also received a variable velocity result in&mdashwhich is excellent for cutting plastic to assist stop melting. 
It will come with a plastic and drywall blade, a steel slash off wheel, and a diamond blade for cutting tile and cement board.  You can understand a lot more about the new Ryboi 1+ HP cut off resource at the website link here if you&rsquore intrigued.
.
For slicing straight traces on the plexiglass, I just lined up a straight edge (scrap piece of wood), clamped and ran the steel blade guard from it to make the reduce.  You can skip the straight edge and freehand these cuts, far too if you have a regular hand. (I don&rsquot haha!)
I did discover it slice very best in this scenario with the switch in reverse. It appeared to not soften that way.
.
I reduce two items equivalent in dimension for every single merchandise I was framing. Then, I was all set to start building the genuine floating image frames.
Simple Do-it-yourself FLOATING Picture Frame Type 1
Style one is my individual preferred, so I&rsquoll start off with it 😊
This distinct floating picture body design and style involves ¾&Key sq. dowels and one×2 board. It is essentially just a 1×2 wrapped around a square dowel body.
.
I utilised ¾&rdquo sq. dowels for this and established up my miter saw to minimize forty five degrees.  Now, you don&rsquot have to miter these.  You can leave it on 90 and make butt joints.  You also don&rsquot need to have a MITER observed for this.  Any observed that you can lower relatively straight with will get the job done great.
.
I basically trimmed four pieces of square dowel so that when healthy alongside one another, they&rsquod be just hardly (like ⅛&Primary) greater than the plexiglass piece I was placing in it.
I used wooden glue to the corners and nailed them jointly with brad nails.  If you are affected individual, and don&rsquot have a nail gun, merely glue and clamp until finally dry.
.
Right after the glue had dried, I slash to suit 1×2 parts with 45 degree mitered corners about this body.  All over again, butt joints are good in this article if you want to skip the mitered corners.
.
I glued and nailed these 1x2s about the edges leaving about ¼&rdquo sticking out the back again aspect of the plexiglass, so that when I put in the two ⅛&Primary plexiglass parts, it&rsquoll be flush across the back side of the frame.
Then, I screwed these twisty tabs into the again sides of the body to keep the plexiglass in position.  I&rsquoll go back again and clean up the sawdust off the plexiglass later on, but for now, I set this off to the side to make the following frame.
Effortless Do it yourself FLOATING Image FRAMES Design and style two
Fashion 2 is a very little easier and is manufactured of 1x2s and ¼&rdquo thick by 1 ⅛&Primary extensive lattice trim.
I started by slicing down the lattice items so it would make a frame that the plexiglass would suit Within.  Again, just like right before, the mitered corners are optional.
At the time I experienced this lattice body slash, I measured its total sizing and slice one×2 parts to make a frame whose general dimensions matched that of the lattice frame. See under one×2 body laying on prime of lattice body&ndashthey&rsquore the exact same dimensions.
I glued and nailed the one×2 body with each other and clamped until dry. Again, you can use super glue or painters tape if you don&rsquot have a nail gun or clamps 🙂
.
Then, I flipped it upside down and glued the lattice frame onto the again.  I utilized a significant item to keep it in place until eventually it was dry, then, I screwed twisty tabs on the again to hold the plexiglass in location. 
Because the lattice is ¼&rdquo thick, and the plexiglass is ⅛&rdquo thick, when the two plexiglass parts are placed inside of, all the things ought to sit flush across the back again just like the last frame.
Yet again, I&rsquoll go back and cleanse the sawdust off later, but for now, I moved on to the previous style frame.
Effortless Do-it-yourself FLOATING Picture Frame Style three
Style three is the exact same principle as design and style 1, but instead of working with 1x2s, I utilised ¼&Key x one ⅛&Prime lattice trim to retain the frame a tiny thinner and a lot more minimalist seeking.
So, I slash ¾&rdquo sq. dowels to make a body the very same sizing or somewhat more substantial than the plexiglass I was framing and glued and nailed it collectively.
Then, I minimize lattice trim to wrap all over that frame. 
I glued the lattice trim on so that there was about ¼&rdquo sticking off the again facet of the square dowel frame so that when the two pieces of ⅛&rdquo plexiglass are put in, it&rsquoll all be flush throughout the back again.
.
I didn&rsquot have any brad nails quick plenty of to nail this body on, so I simply just glued and clamped until eventually it was dry.
If you don&rsquot have clamps, you can use painters tape to kind of wrap about the items to hold till the glue dries OR simply use some super glue or CA glue to support keep items in spot right until the true wood glue is cured.
.
Then, just like the very last two frames, I set up twisty tabs to maintain the plexiglass in position.
FLOATING Picture Frame HANGING Alternatives
The last phase is clean up and hanging.  I utilised some glass cleaner to clear up all the observed dust, then utilized a piece of double sided tape on the back plexiglass piece to make sure the pictures remain in spot, then put the frames back alongside one another.
.
To hang, you can use your standard sawtooth hangers for this.
Or only place it on a shelf.
.
OR, use a drill to drill holes into the corners to operate some paracord and cling it on a piece of wooden dowel you screwed into the wall.
As you can see, generating image frames doesn&rsquot have to be intricate.  This is a great novice task you can tackle with small resources and get as resourceful as you want. 
.
I in fact hung these graphics up in my desk space to enable keep me enthusiastic when doing work alone from residence right now. So, now that my desk area is full, I guess I should really most likely get back to get the job done 😊
I hope you&rsquove savored this minor project.  There are a great deal much more coming your way, so be positive to subscribe to my publication under so you don&rsquot skip out on what&rsquos coming following!
.
And don&rsquot overlook to pin this for afterwards!
Right up until subsequent time, content building 😊